Protect concrete paver driveways, pool decks, and walkways with penetrating sealers formulated for Florida's UV exposure, humidity, and heavy rainfall.
Concrete pavers are porous by design — the mix that gives them their texture and anti-slip properties also makes them highly susceptible to staining, UV bleaching, and moisture absorption. In Southwest Florida, an unsealed concrete paver surface absorbs oil, rust from irrigation water, and algae-feeding organic matter almost immediately. After a few summers without sealing, concrete pavers fade from their original color, develop embedded staining that pressure washing alone cannot remove, and show efflorescence — the white chalky haze caused by salt migration to the surface during wet-dry cycles.
Professional concrete paver sealing prevents these problems by filling the pores that would otherwise absorb staining and moisture. A quality penetrating sealer does not change the appearance of the paver significantly — it makes the surface look clean and fresh while creating an invisible barrier against UV, oil, rust, and biological growth. Water beads on a properly sealed paver surface, and routine cleaning becomes far easier — what previously required pressure washing can often be rinsed clean.
Rain Exterior Home Service provides concrete paver sealing throughout Fort Myers, Cape Coral, Naples, Bonita Springs, Estero, and surrounding Lee and Collier County communities. We use professional-grade penetrating and acrylic sealers matched to the specific porosity and use of your concrete pavers — pool-area, driveway, and walkway applications each have different requirements for slip resistance, UV protection, and cure time. Our process always includes deep cleaning and efflorescence treatment before any sealer is applied.
If your concrete pavers have been neglected for several seasons, they may also need a restoration cleaning to remove deeply embedded staining before sealing. We assess this during the initial inspection and provide an honest recommendation before pricing the job. Ask about our combined cleaning and sealing packages for driveways and pool decks.
We also seal poured concrete — not just pavers. Plain concrete driveways, sidewalks, patios, and pool decks across Southwest Florida face the same enemies: UV fading, oil and rust staining, and algae growth in the surface pores. Concrete sealing after a professional driveway cleaning locks out moisture and staining, keeps the slab looking uniformly clean, and makes every future wash easier. If you are not sure whether your surface is poured concrete or concrete pavers, send us a photo with your quote request and we will spec the right sealer either way.
A penetrating sealer is designed to penetrate the concrete surface and protect it from within — that is our specialty, and for most Fort Myers and North Fort Myers driveways, patios, and pool decks it is the right call. A concrete coating — epoxy, a decorative overlay, or a painted floor system — sits on top of the slab and changes how it looks and wears; it is a different product for a different job, and if that is what your project actually needs, we will say so honestly rather than sell you a sealer. Either way the preparation is identical: the surface professionally cleaned, every crack and joint assessed, and the slab fully dry before anything goes down.
A quality sealer also enhances the surface — it deepens the color of decorative concrete and natural stone, evens out the finish, and makes a garage or lanai concrete floor just as easy to keep clean as the driveway. As a fully insured contractor working across Lee County, we match the product to the surface: penetrating silane/siloxane for plain slabs, film-forming acrylics where sheen is wanted, and stone-safe formulas for travertine and natural stone.
How It Works
We assess the concrete paver condition, check for efflorescence, existing sealer failure, oil absorption, and joint sand depth before selecting the right sealer formulation for your surface.
Concrete pavers are pressure washed and any efflorescence, oil staining, or embedded organic growth is treated with targeted cleaning agents before the main wash. The surface must be chemically clean before sealing.
Concrete pavers must dry fully before sealing — typically 24 to 48 hours. Joints are inspected and refilled with polymeric sand where needed. Damp pavers or empty joints produce visible sealer failures.
A penetrating concrete paver sealer is applied to fill pores and lock out staining, UV, and moisture. We use low-VOC professional formulations safe for pool areas and landscaping.
Common Questions
Yes. Alongside concrete pavers, we seal poured concrete driveways, sidewalks, patios, and pool decks throughout Fort Myers and Southwest Florida. Poured concrete uses penetrating siloxane or acrylic sealers chosen for the slab finish and slip requirements — pool decks get anti-slip rated products. Sealing always follows a deep clean so stains and algae are removed, not locked in.
Not always. Concrete pavers are more porous than clay brick pavers and absorb sealer differently. The best products for concrete pavers are typically penetrating acrylic or polyurethane-based sealers formulated specifically for the higher absorption rate of concrete. Using a sealer designed for clay brick on a concrete paver can result in uneven appearance and faster breakdown. We carry sealer products specific to concrete paver applications.
Quality penetrating sealers on concrete pavers last approximately 2 to 3 years in Southwest Florida. Surface-applied (film-forming) sealers may need attention every 18 to 24 months on high-traffic areas like driveways and pool decks, where UV, foot traffic, and water exposure wear the coating faster. The clearest sign of sealer breakdown is that the surface no longer beads water and begins absorbing staining — at that point, re-sealing should be scheduled promptly.
Yes. We use penetrating sealers and acrylic formulations that are safe for pool areas — they are non-toxic once cured and will not affect pool water chemistry. Pool-area sealers must also provide some slip resistance; we select products with appropriate anti-slip ratings for wet environments. We avoid high-gloss film-forming sealers for pool decks because they can become slippery when wet.
Efflorescence is a white, chalky deposit formed when water-soluble salts migrate to the surface of concrete pavers and crystallize as the water evaporates. It is very common in Southwest Florida due to the wet-dry cycles of the rainy season. Efflorescence is not a structural problem but must be treated and neutralized before sealing — sealing over active efflorescence will trap the salts and cause clouding under the sealer coat. We treat efflorescence as part of our pre-sealing cleaning process.
A high-gloss film-forming sealer can reduce traction when wet — this is why we do not recommend glossy sealers for pool decks and pool areas. Penetrating sealers do not significantly change surface texture and maintain traction when wet. For areas that receive water regularly, we recommend either a penetrating sealer with no gloss or a sealer with an anti-slip aggregate added. We discuss finish options with you before selecting a product.
What Homeowners Say
"He gave me a very competitive quote but did tell me I should wait 6 months after the driveway was installed before seal coating for best results… he just finished my driveway today and it looks awesome. Randell was very professional, took his time to blow off the driveway, spray it down with a cleaning acid and then added two coats of sealer… I would absolutely recommend Randell to seal coat your driveway or pool lanai."
"Randell did a great job. While cleaning and sealing the pavers, he was able to remove some stains that I didn't think would come out. Great job!"
"Showed up on time and provided professional service at a reasonable cost!"
Serving Fort Myers, Cape Coral, Naples, Bonita Springs, and all of Southwest Florida. Most jobs quoted within 24 hours.
Rain Exterior Home Service
We Regularly Serve Homeowners in Southwest Florida: